Question about V7Pro DiSEqC

V7 TT Pro / V7S HD /V7 Plus/V7 S2X /V7PRO/ V7 TT

Moderators: admin, GTMedia Team

brisel
Posts: 33
Joined: Mon Jan 11, 2021 9:45 pm

Re: Question about V7Pro DiSEqC

Post by brisel »

Owen, thank you for fast reply. I tried a splitter but it seems that it did not work, but maybe it did not have good cable connection. In next few weeks I will try to obtain one 1.1 diseqc (I have found on 4x1). I also have on 8x1 but for 3 sattelites this 4x1 should be enough

User avatar
Feralkiwi
网站管理员
Posts: 8339
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: Question about V7Pro DiSEqC

Post by Feralkiwi »

brisel wrote:
Sun Jan 09, 2022 10:13 pm
Owen, thank you for fast reply. I tried a splitter but it seems that it did not work, but maybe it did not have good cable connection. In next few weeks I will try to obtain one 1.1 diseqc (I have found on 4x1). I also have on 8x1 but for 3 sattelites this 4x1 should be enough
With the 4 port make sure that it is a DiSEqC 1.1, not a 1.0 like you have.

I once used two 4 port 1.0 switches with ports 1,2 3 connected in a splitter then one cable to the second 4 port switch for three sats there and one on port four at the first switch. Saved running three cables. After I got a 1.1 switch I took the splitter out.

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

User avatar
Feralkiwi
网站管理员
Posts: 8339
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: Question about V7Pro DiSEqC

Post by Feralkiwi »

brisel wrote:
Sun Jan 09, 2022 10:13 pm
Owen, thank you for fast reply. I tried a splitter but it seems that it did not work, but maybe it did not have good cable connection. In next few weeks I will try to obtain one 1.1 diseqc (I have found on 4x1). I also have on 8x1 but for 3 sattelites this 4x1 should be enough
Just another thing with splitters.

Were both ports "Power Pass"? You need the power to go past to the LNB.

Was the splitter 950-2100MHz? There are splitters that are UHF only, 150-850MHz.

Was it satellite only, not a UHF / Satellite separator?

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

gater140
Posts: 22
Joined: Fri Dec 31, 2021 11:11 pm
Location: Townsville

Re: Question about V7Pro DiSEqC

Post by gater140 »

I had the same problem on my V7 Pro.
Did a system upgrade and it fixed it

Ron

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

Уважаемые специалисты здравствуйте! я столкнулся с проблемой управления антеннами дисеком у меня антенна 120см, 60см.Т-90, 90см Горизонт - горизонт, дисеки 1\4. 1\8. 1\16 ранее работало на хваленом ресе НТВ+ который я не хвалю, часто зависает и на триколоре, приобрел V7 PRO, но к моему великому сожалению " DiSEgC" не желает функционировать, а так как я не силен в прошивках и в моей деревне спецов нет прошу помощи. SOS!!! ежели Вас сильно не затруднит инструкцию пожалуйста по шаговую. ВСЕМ СПАСИБО ! С УВАЖЕНИЕМ Леонид.
Dear experts, hello! I ran into a problem with controlling antennas with a disk. My antenna is 120cm, 60cm. T-90, 90cm Horizon - horizon, disks 1/4. 1\8. 1\16 previously worked on the vaunted NTV resource, which I do not praise, often freezes on the tricolor, I purchased V7 PRO, but to my great regret "DiSEgC" does not want to function, and since I am not strong in firmware and there are no specialists in my village I ask for help. SOS!!! If you are not much complicate the instructions, please step by step. THANKS TO ALL ! Sincerely, Leonid.

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

Can you confirm, how many satellites you are receiving, what switches you have within the system.
We should be able to talk you through on how to solve this issue for you.
If you can put photo's up, it will be a great help.

Den

User avatar
Feralkiwi
网站管理员
Posts: 8339
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: Question about V7Pro DiSEqC

Post by Feralkiwi »

There are two types of DiSEqC switch, 1.0 and 1.1

Most 2 and 4 port DiSEqC switches are 1.0, so use the setting in the antenna setting for that.
8 port switches are mostly DiSEqC 1.1, so use that in the antenna settings.

Note that if you are using both GT Media sends the 1.1 command first.

Also you can not use a 22kHz switch before a DiSEqC switch.
DiSEqC commands are sent using the 22kHz tone in a digital pulse, so any 22kHz switch before the DiSEqC switch will change with each data bit and stop the DiSEqC commands from passing through.

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro

Post by ЛЕОНИД »

Доброе время уважаемые специалисты ! По спутникам я прямо и просто ответил "мотоподвес горизонт - горизонт " антенна "Т-90" и еще несколько разно калиберных. По DiSEqC "S16/1PC-W3" " 8iN1 DiSEqC 1.0+1.2" сборка "1.0 - 1.1" . Короче говоря DiSEqC 1.0 в работе только на телевизоре, НТВ+ DiSEqC тоже не желает работать,но там есть кому смотреть, не трогаю, правда в настоящее время на спутниках халявы стало мало, Ну...
Написал лишку, прастите.
Ежели Вас не очень затруднит прошу пошаговую инструкцию обновления , переустановки ПО. у самого тяму не хватает,возраст. Пожалуйста разжевать. Спасибо ! 73!
С уважением Леонид

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

ДОБРОЕ ВРЕМЯЧКО ! ГОСПОДА Den И Оуэн ! ИЗВИНЯЮСЬ, СРАЗУ НЕ ВЪЕХАЛ, КОМУ ТОЛКУЕМ ЗА DiSEqC, ТАЗИКИ, СПУТНИКИ, МИ ЭТО ДАВНЕНЬКО ПРОГЛОТИЛИ, ВЫ НЕ ОБИЖАЙТЕСЬ, НО *SOS!* ПОДАН, прошивка * V7Pro*, надо ткнуть меня носом и толком объяснить как это делается, если имеем знания.
С уважением Леонид

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

Can we confirm on how many satellite dishes you have, from what i can make out you have one 120cm, one 60cm, is it one or two 90cm dishes.
The channels that you watch, are they in the (C-Band) or (KU-Band).
What satellites are each dish pointing at, the (DISEQ) switch that you are using, how many (inputs) does it have.

Den

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

УВАЖАЕМЫЙ Den! Зачем ми будем считать тарерьки и сантиметры, на Т-90, 12 конвертеров на поворотке 2, С и Ку диапазоны. Вопрос в работе управления переключателями – DiSEqC В V7Pro*, а не КРУТИЛКАМИ ТАРЕЛОК.
С уважением Леонид

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

What i am trying to get at, is how have you got your set up.
How many dishes have you got, what satellites are they pointing at.
This will take a while, with more information, we will be able to get the VPro set up .

Den

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

УВАЖАЕМЫЙ Den!
Зачем, понять нуна одно, не работает программа управления коммутаторами – DiSEqC В * V7Pro*, а остальное хозяйство, спутники, конвертеры, блок DiSEqC *S16/1PC-W3*, фидера. В рабочем состоянии. И забивать умную голову ерундой не следует.
С уважением Леонид

User avatar
Feralkiwi
网站管理员
Posts: 8339
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: Question about V7Pro DiSEqC

Post by Feralkiwi »

Hi

From what I can read of your translated words, I think you are using both DiSEqC 1.1 AND 1.0

Please note that GT Media software sends (in error I think) DiSEqC 1.0 first and then the 1.1 command.
This means that if you have the 1.1 switch first as is normal, the command for the 1.0 switch is not actioned until the V7Pro resends the commands.

Also this. I do not think you have one, but you can not use a 22kHz switch before any DiSEqC switches.

Another thing that happens with GT Media units is the over current protection trips easily.
As the 1.1 switch port is selected and powers up the 1.0 switch and the LNB, there is often a overcurrent trip with some switch / LNB types.
To stop this I have found a tone type finder or a splitter in the cable at the set top box adds some impedance and stops this.
Also a 2A power supply helps as there is less voltage drop at high current times, like the power surge on LNB power up.

As these over current trips can happen, I recommend using any USALS or DiSEqC 1.2 motors on port one of the DiSEqC 1.1 switch, as port one is the default.

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

УВАЖАЕМЫЕ ПРОФЕССИОНАЛЫ И ЛЮБИТЕЛИ DEN & OUEN ! ЗДРАСЬТЕ ВАМ !
Я ПРАСЮ ПРАЩЕНИЯ ЗА ПЕРЕВОДЧИКОВ, У МЕНЯ ПОХОЖЕ БЫЛ КАЗУС СО СЛОВАКИЕЙ И АВСТРАЛИЕЙ, А Я И ПО РУССКИ МЫСЛЮ С ОШБКАМИ, ПРОСТИТЕ Попробую наших переводчиков. Сегодня не поленился снял почти все DiSEqC, моторы не трогал, т.к один вообще не использую другой только при +температуре с позиционером, большей люфт, да и насиловать не зачем.
Проверил все коммутаторы на приемнике телевизора LG все в рабочем состоянии от «LG и DRE-5000» они и на чердаке работали. Я не знаю почему Ваша 200% УВЕРЕННОСТЬ в неисправных коммуаторах, а не в работе « V7PRO « На котором пытался рассмотреть подачу сигнала на комм.. какая то не понятная билиберда, на LG, DRE-5000 нормально правда быстро идет сигнал и все в работе. Вот такие пироги
С уважением Леонид
----------=================================================
Dear professionals and lovers of Den & Ouen! Hello you!
I am pushing for the translators, I seemed to have a casus with Slovakia and Australia, and I think in Russian with scraps, I'm sorry I will try our translators. Today I was not too lazy to take off almost all Diseqc, I didn’t touch the engines, because one does not use the other at all at +temperatures with the poster, the larger backlash, and why there is nothing to rape.
I checked all the switches on the LG TV receiver all in working condition from LG and DRE-5000 they worked in the attic. I don’t know why your 200% confidence in faulty utilities, and not in the work of “V7PRO” on which I tried to consider the signal for the commune .. some kind of Biliberda, which is not clear to LG, DRE-5000 normally the signal is normal and everything is in work. . These are the pies
Sincerely Leonid

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

ДВА РАЗА БЫЛО НА АНГЛИЙСКОМ :?:

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

Can you put any photo's on here, of the switches that you use, and were they are fitted within your system, with the leads from the dishes.
Having these will be a great help, also can make a diagram of your satellite system, something like this.

Den
Attachments
101_1736.JPG
101_1736.JPG (1.04 MiB) Viewed 5598 times

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

Руководство по эксплуатации EMP-Centauri S16 / 1PCP-W3 страница 3
Переключатель Diseqc
1
2
3
4
СТРАНИЦА
3
4ВПЕРЕД
ЗАКЛАДКИ
Поиск в этом руководстве
РЕКЛАМА

эксплуатацияНастройка DIP-рычагов спутникового приемникарежим1DiSEqC 1.0 ВЫКЛ ВЫКЛ DiSEqC 1.0 – зафиксированная команда 1-4 (A–D), относитсяDiSEqC 1.1 ВКЛ ВЫКЛ DiSEqC 1.1 – незафиксированная команда 1-16, относитсяDiSEqC 1.0ОТКЛЮЧЕНО ПРИ DiSEqC 1.0 – зафиксированная команда 1-4 (A–D) ++DiSEqC 1.1DiSEqC 1.2 ВКЛ. ПРИ 16 положениях двигателя: заданные номера (положения двигателяПримечания к настройке:Погружные рычаги 3 и 4 не используются•любое изменение настроек поворотных рычагов будет применено только после сброса•(отсоединение и повторное подключение кабеля OUT)процедура настройки каждого приемника может отличаться, следуйте инструкциям•руководство по эксплуатации вашего приемника7) БезопасностьПо соображениям безопасности изделие и проводка, в которой оноподключенный, должен быть надлежащим образом заземлен.Убедитесь, что антенныgrounded properly. Connect all devices to power grid only after allconnections are finished and checked. Never work on the wiring (includingsatellite receivers, TVs) during or before a storm. A lightning stroke into theantenna may cause dangerous overvoltage in the product metallic parts.8) Product MaintenanceAlways disconnect the product from the wiring before performing any maintenanceof the product. If you have to enter places with a risk of fall, pay attention to yoursafety. Use only dry cloth to clean the product and do not use any liquid agents.Coaxial cables installed outdoors should be replaced once in a few years.Unscrew all F connectors and clean connector contacts, resp. shorten the coaxialcable by approx. 2 cm, every 2 years.2непосредственно на входы SAT 1-4 Внепосредственно на входы SAT 1-16 ВDiSEqC 1.1 – незафиксированная команда 1-4,его комбинации относятся к входам SAT 1-16 Вблоки памяти) 1-16 относятся к входам SAT 1-16В новом продукте; предварительные настройки могут быть обновлены с помощьюпроцедура поиска и сохранения новой позиции3 of 4

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

I am adding more photo's to help you.
When you have two dishes going into the receiver, you use a (DISEQ 2 Way Switch), on the receivers setting, the (Diseq is 1.0)

Den
Attachments
101_1740.JPG
101_1740.JPG (1.08 MiB) Viewed 5595 times

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

When you have four dishes, you use a (4 Way Diseq Switch). The receivers setting on the (Diseq is 1.0)

Den
Attachments
101_1741.JPG
101_1741.JPG (1.07 MiB) Viewed 5594 times

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

When you have up to eight dishes, you use a (8 Way Diseq Switch), with the receivers setting, this time (Diseq 1.1)

Den
Attachments
101_1742.JPG
101_1742.JPG (1.11 MiB) Viewed 5593 times

STRETCH
Posts: 3642
Joined: Mon Jan 09, 2017 2:31 pm
Location: West Midlands UK

Re: Question about V7Pro DiSEqC

Post by STRETCH »

A couple of photo's of a 4 way and 8 way diseq switches.

Den
Attachments
101_1743.JPG
101_1743.JPG (1.36 MiB) Viewed 5587 times
101_1745.JPG
101_1745.JPG (1.3 MiB) Viewed 5587 times

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

Я НЕ ВИЖУ СВОИХ ВЛОЖЕНИЙ, ЧТОЙ ТО НЕ ТАК ДЕЛАЮ.

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

ФОТО КОММ...
ФОТО КОММ...
Dq C.JPG (100.41 KiB) Viewed 5562 times
Attachments
Dq C.JPG
Dq C.JPG (100.41 KiB) Viewed 5562 times

ЛЕОНИД
Posts: 13
Joined: Fri Dec 10, 2021 6:41 am

Re: Question about V7Pro DiSEqC

Post by ЛЕОНИД »

ЧАСТЬ Д -КОВ
ЧАСТЬ Д -КОВ
ААААААААААААААА.jpg (138.87 KiB) Viewed 5561 times

Post Reply

Return to “GTMEDIA V7 SERIES”