Decoder Free-Sat V7 Combo in blocco

V7 TT Pro / V7S HD /V7 Plus/V7 S2X /V7PRO/ V7 TT

Moderators: admin, GTMedia Team

Post Reply
siculorum
Posts: 4
Joined: Wed Sep 12, 2018 8:13 am

Decoder Free-Sat V7 Combo in blocco

Post by siculorum »

Salve ho un Decoder Free-Sat V7 Combo che non funziona più , Ho caricato tramite porta seriale ,col programma Tcom, molte volte il firmware tramite Sonata DDr3 Che carica il download per due volte ma quando accendo il decoder parte con Boot Load e si ferma con 4 trattini luminosi e il led acceso.

User avatar
Feralkiwi
网站管理员
Posts: 8339
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: Decoder Free-Sat V7 Combo in blocco

Post by Feralkiwi »

GT Media units start after reset in PAL TV mode.

Try this.

Owen
Added fast key to switch video output mode or format.
we try to support some old TV or some signal mode TV
Press menu key to main menu.(Panel show "----")
press Green key to switch NTSC/PAL, the panel will show "PAL " or "NTSC"
Press Stop key to switch the video format
PAL mode : the panel will show "576I" -- "576P" -- "720P"(50HZ) --"1080I"(50HZ) --"1080P"(50HZ)
NTSC mode : the panel will show "480I" -- "480P" -- "720P"(60HZ) --"1080I"(60HZ) --"1080P"(60HZ)
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

siculorum
Posts: 4
Joined: Wed Sep 12, 2018 8:13 am

Re: Decoder Free-Sat V7 Combo in blocco

Post by siculorum »

Provato col tasto verde vado su Pal 720p ma non lo memorizza col tasto Menu' o Exit tornano i ---- e il led giallo ma non si collega con la tv con HDMI

siculorum
Posts: 4
Joined: Wed Sep 12, 2018 8:13 am

Re: Decoder Free-Sat V7 Combo in blocco

Post by siculorum »

Non funziona la porta HDMI solo con i cavi audio video il decoder si collega con la tv.
Grazie per la risposta.

User avatar
Feralkiwi
网站管理员
Posts: 8339
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: Decoder Free-Sat V7 Combo in blocco

Post by Feralkiwi »

Other users have had their units loose HDMI output.

Some have reported this was due to lightning or other electrical faults.

To help prevent this again if that happened to your unit, add a AV cable between the unit and the TV as that adds more ground wire to help pass the ground currents from your satellite dish to the earth on your TV.
With just the HDMI cable, all ground currents pass through the HMDI.

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

fritz_ht
Posts: 6
Joined: Thu Jun 24, 2021 1:34 pm

Re: Decoder Free-Sat V7 Combo in blocco

Post by fritz_ht »

siculorum wrote:
Fri Jul 23, 2021 4:19 pm
Non funziona la porta HDMI solo con i cavi audio video il decoder si collega con la tv.
Grazie per la risposta.
Ciao ho lo stesso problema che l'HDMI non funziona più, solo che non ricordo ma il cavo audio/video è in dotazione? Ho controllato nella scatola e non l'ho, non vorrei averlo tolto ed essere finito nella rumenta che ho in giro per casa :D

Fabrizio

fritz_ht
Posts: 6
Joined: Thu Jun 24, 2021 1:34 pm

Re: Decoder Free-Sat V7 Combo in blocco

Post by fritz_ht »

Feralkiwi wrote:
Thu Jul 22, 2021 9:17 pm
GT Media units start after reset in PAL TV mode.

Try this.

Owen
Added fast key to switch video output mode or format.
we try to support some old TV or some signal mode TV
Press menu key to main menu.(Panel show "----")
press Green key to switch NTSC/PAL, the panel will show "PAL " or "NTSC"
Press Stop key to switch the video format
PAL mode : the panel will show "576I" -- "576P" -- "720P"(50HZ) --"1080I"(50HZ) --"1080P"(50HZ)
NTSC mode : the panel will show "480I" -- "480P" -- "720P"(60HZ) --"1080I"(60HZ) --"1080P"(60HZ)
On my V7 Pro PAL/NTSC with Green Key is not working. Stop key is working but apparently is already in 1080p but I can't see nothing on the screen, it's like is not connected, I think the HDMI port is dead :( .

fritz_ht
Posts: 6
Joined: Thu Jun 24, 2021 1:34 pm

Re: Decoder Free-Sat V7 Combo in blocco

Post by fritz_ht »

fritz_ht wrote:
Mon Jul 26, 2021 9:03 am

On my V7 Pro PAL/NTSC with Green Key is not working. Stop key is working but apparently is already in 1080p but I can't see nothing on the screen, it's like is not connected, I think the HDMI port is dead :( .
I've connected the analog output using a jack to rca audio cable, the red audio is good for video and the receiver is working, I can see the channels so is definitively the HDMI dead. I should have somewhere the proper analog cable popped out from some other product, I just have to find it :)

User avatar
Feralkiwi
网站管理员
Posts: 8339
Joined: Fri Aug 12, 2016 6:51 am
Location: New Zealand

Re: Decoder Free-Sat V7 Combo in blocco

Post by Feralkiwi »

You need a 3.5mm plug that is 17mm long.

Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.

fritz_ht
Posts: 6
Joined: Thu Jun 24, 2021 1:34 pm

Re: Decoder Free-Sat V7 Combo in blocco

Post by fritz_ht »

Feralkiwi wrote:
Mon Jul 26, 2021 9:05 pm
You need a 3.5mm plug that is 17mm long.

Owen
Thanks Owen,
found one from my old Sony DV Camera, I don't know the lenght but it's working, so the problem is definitively the HDMI dead.

Post Reply

Return to “GTMEDIA V7 SERIES”