GTMEDIA Forum

1.录制节目一定分段在未达到指定时间的情况下被终止
2.SAT2IP播放一定时间被终止
3.画面抖动的厉害，损害液晶显示器面板，需要增加去隔行算法

1. recording a certain segment of the program is terminated without reaching the specified time
2. Sat2ip playback is terminated for a certain time
3. the screen jitter is severe, which damages the LCD panel, so it is necessary to add the de interlacing algorithm

I have found that if you press the power button on the remote while the unit is booting it will start in UP9.
UP9 screen is a software upgrade / recovery screen.
This is easily done if you press the power button too many time as you power on.

This may be why so many users are finding their units in this screen.


The UP9 screen is entered by repeat pressing the power on button while booting.

To clear, just power off at the wall or the switch on the top of the unit and power on again.

Owen

Hello GTMedia Team

viewtopic.php?p=96078#p96078

Thank you
skewer

It is so irresponssible by gtmedia team
We are waiting firmware v8 nova since 5 months but sadly have to say
They are just ignoring v8 nova's bug and Select All deselect Options under Channel list

anmoolpk wrote: ↑

Thu Apr 15, 2021 3:19 am

It is so irresponssible by gtmedia team
We are waiting firmware v8 nova since 5 months but sadly have to say
They are just ignoring v8 nova's bug and Select All deselect Options under Channel list

I think that you are right
I also waiting firmware for Select All Options under channel list
I tired to deleting many channels by using V8 tool in pc
Whenever i ask to team for above option then they are deleted my post
It is

ameenjuz wrote: ↑

Thu Apr 15, 2021 3:26 am

anmoolpk wrote: ↑

Thu Apr 15, 2021 3:19 am

It is so irresponssible by gtmedia team
We are waiting firmware v8 nova since 5 months but sadly have to say
They are just ignoring v8 nova's bug and Select All deselect Options under Channel list

I think that you are right
I also waiting firmware for Select All Options under channel list
I tired to deleting many channels by using V8 tool in pc
Whenever i ask to team for above option then they are deleted my post
It is

Exactly right point i m waiting firmware v8 nova too

Hi
Now all Nova models has updated with the all delete options. Please refer to each model download section.

Hello.
The problem is with the GTmedia V8X.
I cannot search some transpoders from the Hot Bird 6/8/9 satellite.
Transponder 10719 is ok.
Transponder 11411 and 11449 no quality signal (signal strength 92%).
I have installed the latest software update.
I bought GTMedia on alliexpress.
I was sent to this address for help.

I have the same receiver, i can pick up all three transponders (strength93% /quality 85%), with a 110cm dish here in the UK.
Have you got the correct settings for the lnb (9750-10600), have you any switches between the lnb and receiver, what size dish, etc.
With more information we will be able to pin point the issue.

Den

The problem only occurs with certain transponders.
The receiver is factory set.
LNB 9750-10600
DiseqC1.0 None
DiseqC1.1 None
22kHz auto
Polarity auto

I have a multiswich for 8 receivers.
I checked the receiver on other ports, the problem occurs on every port.
I have 5 other receivers.
Neither of them have trouble with the signal.
Signal strength 90-93%.
Signal quality 80-85%.
100cm antenna.

ixi3 wrote: ↑

Thu Apr 29, 2021 3:13 pm

......Transponder 11411 and 11449 no quality signal (signal strength 92%)......

I have had the high signal, but no quality problem myself.
On doing a full scan I discover channels are missing which I know exist.
it is usually when the symbol rate in the satellite transponder entries are wrong or have changed since the receiver database was created.
Check to make sure that those 2 have entries of 27,500.

Another test would be to set up another satellite (I call mine 'Test'), edit the LNB osc frequencies to 9750 - 10600 & do a blind scan.
I do this for new satellites & later edit the name & orbital position.

Pete

ixi3 wrote: ↑

Thu Apr 29, 2021 3:13 pm

Transponder 10719 is ok.
Transponder 11411 and 11449 no quality signal (signal strength 92%).

The first TP is vertical, the second and third horizontal. I guess that the problem is here: your antenna set-up doesn't permit the correct managing of the correct voltage towards the lnb. Instead of switch to 18 V, it remains lower.

evarese wrote: ↑

Fri Apr 30, 2021 10:27 am

ixi3 wrote: ↑

Thu Apr 29, 2021 3:13 pm

Transponder 10719 is ok.
Transponder 11411 and 11449 no quality signal (signal strength 92%).

The first TP is vertical, the second and third horizontal. I guess that the problem is here: your antenna set-up doesn't permit the correct managing of the correct voltage towards the lnb. Instead of switch to 18 V, it remains lower.

I wrote above that other receivers (3 pieces) search for channels on this transponder without any problems.

From what you are saying , you have tried every port in your receiver on the (diseq1.1) side of the receiver, some of the settings are (1 CasM1;Port 1 / 1CasM2;Port 4 / 1CasM3;Port 2 / 2Cas:Port2 etc.
At one time i had 7 lnb's going through a 8 way diseq switch, it took me a while to get the correct settings, i now have the dish on a motor.

Den

ixi3 wrote: ↑

Fri Apr 30, 2021 12:37 pm

I wrote above that other receivers (3 pieces) search for channels on this transponder without any problems.

Evidently the other 3 receivers' setting is correct. What i wrote in my post is exactly the same matter, using different words only!

evarese wrote: ↑

Fri Apr 30, 2021 1:59 pm

ixi3 wrote: ↑

Fri Apr 30, 2021 12:37 pm

I wrote above that other receivers (3 pieces) search for channels on this transponder without any problems.

Evidently the other 3 receivers' setting is correct. What i wrote in my post is exactly the same matter, using different words only!

From the previous statement, I understood that the problem is the antenna installation. Except that the settings of the receiver. So what is wrong with the receiver or antenna installation?

Can you please confirm what your settings are for your 13e satellite.

Den

STRETCH wrote: ↑

Fri Apr 30, 2021 4:33 pm

Can you please confirm what your settings are for your 13e satellite.

Den

What are the parameters?

What diseq 1.1 setting have you got for 13e, lnb etc.

Den

Diseqc 1.1- none

I did not check the DiseqC switches.
I use one satellite so they are not needed. So far I have used 8 different satellite receivers and all diseqc switches were off.

Above, you wrote "I have a multiswich for 8 receivers." This means that you have only one dish pointed @ 13° E and several receivers connected through the multiswitch that you switch on one by one?
If yes, have you tried to connect the V8X directly to the antenna? Please let us know if this configuration is working right.

I use 5/8 multiswich.
I tried to perform a full scan and the receiver found the transponders with which there was a problem.
He was picking up their signal correctly.
Unfortunately, it stopped receiving the signal correctly from others.
After restarting the receiver, the situation returned to the initial state.
I turned on diseqc 1.0. The receiver is working properly.
He finds everything.
Is it the fault of the software?
Diseqc is used to change satellites.
I use one.
That's why I have Diseqc turned off in every receiver and everything works as it should.
I guess I don't understand something?

What you not tell us all, is what is the whole set up of your satellite system.
Do you have one dish going to a (multi switch) with receivers from that. / or do you have a few dishes at other satellites with a diseq switch.
How many receivers do you have and how many are on at any one time.
With this sort of information, it may be better to have a (quad lnb) and run a cable to each receiver.

Den

I have:
100cm antenna.
LBN Quattro
Multiswich 5/8 (5 in / 8 out)
5 receivers connected to the multswich each with a separate cable.
It is sometimes possible for all receivers to work simultaneously.

Instead of the multi-switch, you could use a (Octo lnb)(8 way), it may mean more cable, direct from the lnb to each receiver.
This may help with losing 11411 / 11449 which are both (H), seeing that you will have (8 universal lnb's) within the casing.

Den