bug on v8 nova blue using Diseq switch 4x1
Moderators: admin, GTMedia Team
bug on v8 nova blue using Diseq switch 4x1
When i connect 7w on port 4 or 3 or 1 using diseq switch then shows signal good
If i disable switch 1.0 port but do not disconnect signal during connected diseq
I think this is bug of v8 nova- Attachments
-
- 20210504_035835.jpg (2.06 MiB) Viewed 774 times
Re: bug on v8 nova blue using Diseq switch 4x1
When you change the DiSEqC command setting in the antenna menu to "Disabled" it does not send any command, so your switch stays in the last port you had it set until you power off that switch.
With a DiSEqC setting on "Disabled" the unit expects that you have no switch.
If you leave that satellite to another one that has a DiSeqC port setting it will set the switch to that port.
You could use the polarity setting from Auto to V to H and then to "OFF". Off will power off your LNB and switch and default it to port one.
This is just a general settings thing.
The default when you power up a switch is port one.
All satellite units will do this as with disabled they all expect you have no switch.
Owen
With a DiSEqC setting on "Disabled" the unit expects that you have no switch.
If you leave that satellite to another one that has a DiSeqC port setting it will set the switch to that port.
You could use the polarity setting from Auto to V to H and then to "OFF". Off will power off your LNB and switch and default it to port one.
This is just a general settings thing.
The default when you power up a switch is port one.
All satellite units will do this as with disabled they all expect you have no switch.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: bug on v8 nova blue using Diseq switch 4x1
Thanks for quick replyFeralkiwi wrote: ↑Tue May 04, 2021 3:32 amWhen you change the DiSEqC command setting in the antenna menu to "Disabled" it does not send any command, so your switch stays in the last port you had it set until you power off that switch.
With a DiSEqC setting on "Disabled" the unit expects that you have no switch.
If you leave that satellite to another one that has a DiSeqC port setting it will set the switch to that port.
You could use the polarity setting from Auto to V to H and then to "OFF". Off will power off your LNB and switch and default it to port one.
This is just a general settings thing.
The default when you power up a switch is port one.
All satellite units will do this as with disabled they all expect you have no switch.
Owen
I have 3 dishes and 4 satellites are running in 4x1 Diseqc switch
One big dish has 2 lnb and another one one lnb
How can i set diseq port properly on v8 nova
Because i have some issue 2 satellites
Sometime no signal issue during changing the channel
I think that i m missing something
Can you explain what m i doing wrong
Re: bug on v8 nova blue using Diseq switch 4x1
4 port DiSEqC switches will be damaged if you have shorted the input with the power on.
I have done this a few times.
After the short, the port is powered on all the time. Any TP frequency that has the same IF frequency in the LNB cable will be corrupted and not viewed.
Check your 4 port switch. I use a tone type finder (the sort with the moving needle and LED's for H, V, 22kHz etc.) and set the switch to port one and check that port 2, 3 and 4 do not have power. Then do this again with port 2 set to check port one.
If you do not have a tone type finder test with one dish, set to port one and connect the dish to 2, 3, and 4 and then power on the LNB power and see if signal is received.
You could also use a multi meter to test for power on each port.
Never connect dish LNB cables with the power on.
Owen
I have done this a few times.
After the short, the port is powered on all the time. Any TP frequency that has the same IF frequency in the LNB cable will be corrupted and not viewed.
Check your 4 port switch. I use a tone type finder (the sort with the moving needle and LED's for H, V, 22kHz etc.) and set the switch to port one and check that port 2, 3 and 4 do not have power. Then do this again with port 2 set to check port one.
If you do not have a tone type finder test with one dish, set to port one and connect the dish to 2, 3, and 4 and then power on the LNB power and see if signal is received.
You could also use a multi meter to test for power on each port.
Never connect dish LNB cables with the power on.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: bug on v8 nova blue using Diseq switch 4x1
i don't find toturials of gtmedia channel on youtube about diseq switchFeralkiwi wrote: ↑Tue May 04, 2021 8:46 pm4 port DiSEqC switches will be damaged if you have shorted the input with the power on.
I have done this a few times.
After the short, the port is powered on all the time. Any TP frequency that has the same IF frequency in the LNB cable will be corrupted and not viewed.
Check your 4 port switch. I use a tone type finder (the sort with the moving needle and LED's for H, V, 22kHz etc.) and set the switch to port one and check that port 2, 3 and 4 do not have power. Then do this again with port 2 set to check port one.
If you do not have a tone type finder test with one dish, set to port one and connect the dish to 2, 3, and 4 and then power on the LNB power and see if signal is received.
You could also use a multi meter to test for power on each port.
Never connect dish LNB cables with the power on.
Owen
how to set cascade option what is 1casM1 port under diseq 1.1 how to use this option
Re: bug on v8 nova blue using Diseq switch 4x1
When you open the DiSEqC 1.1 options, I move all the way down the list to the ones that offer port 1 to port 16.
As for the "1casM1 port" I never did work out what they mean.
These 1.1 options are used with 8 port uncommitted switches.
The GT Media V7 units only offer the port 1-16 options in the DiSEqC 1.1 menu.
DiSEqC 1.1 is use by 8 port switches only. DiSEqC 1.0 4 port switches will not work with those 1.1 settings.
For any 2 way or 4 way 1.0 switches, just use the port numbers for those on the 1.0 menu.
Cascade switching allows user to have a 8 port 1.1 switch first and then 4 port 1.0 switches second on each port.
8 x 4 = 32 LNB's / dishes. 22kHz switches can be used after that to double it to 64. Universal LNB's cannot use both lower and high bands be through 22kHz switches as they use 22kHz to change bands.
22kHz switches can not be use before a DiSEqC switch.
Owen
As for the "1casM1 port" I never did work out what they mean.
These 1.1 options are used with 8 port uncommitted switches.
The GT Media V7 units only offer the port 1-16 options in the DiSEqC 1.1 menu.
DiSEqC 1.1 is use by 8 port switches only. DiSEqC 1.0 4 port switches will not work with those 1.1 settings.
For any 2 way or 4 way 1.0 switches, just use the port numbers for those on the 1.0 menu.
Cascade switching allows user to have a 8 port 1.1 switch first and then 4 port 1.0 switches second on each port.
8 x 4 = 32 LNB's / dishes. 22kHz switches can be used after that to double it to 64. Universal LNB's cannot use both lower and high bands be through 22kHz switches as they use 22kHz to change bands.
22kHz switches can not be use before a DiSEqC switch.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: bug on v8 nova blue using Diseq switch 4x1
I want to use 8x1 diseq 1.1
If i have 8 satellites running using diseq 1.1
Can i put following way on v8 nova blue?
Lnb1 to 2cas port1
Lnb2 to 2cas port2
Lnb3 to 2cas port3
Lnb4 to 2cas port4
Lnb5 to 2cas port5
Lnb6 to 2cas port6
Lnb7 to 2cas port7
Lnb8 to 2cas port8
If i have 8 satellites running using diseq 1.1
Can i put following way on v8 nova blue?
Lnb1 to 2cas port1
Lnb2 to 2cas port2
Lnb3 to 2cas port3
Lnb4 to 2cas port4
Lnb5 to 2cas port5
Lnb6 to 2cas port6
Lnb7 to 2cas port7
Lnb8 to 2cas port8
Re: bug on v8 nova blue using Diseq switch 4x1
You will be able to use the diseq 1.1 settings on the nova blue, which may be just numbered as port 1 to port 8.
Den
Den