Boot se enciende y se apaga
Moderators: admin, GTMedia Team
Boot se enciende y se apaga
Hola no se si me ha salido defectuoso o que le ha pasado a mi v9 me ha funcionado durante 4 meses, y desde entonces solo se enciende carga, se pone el canal y se apaga y lo tengo con un refrigerador, no me deja meterle ninguna actualización.
Re: Boot se enciende y se apaga
Do you mean that your V9 is not starting?
If it powers on but does not complete the boot and stays with no picture to the TV and only a single green light then you can try a flash.bin recovery.
flash.bin recovery is done like this.
Place a copy of the unpacked software (the .bin file) on a USB stick and rename it "flash.bin"
With the USB in the unit, power on while repeat pressing "Menu" on the remote. You must use the V7 remote on the V7.
The unit should reload the software.
Also other users say that you must use a USB stick, not a card holder etc and that stick must be 32Gb or under.
Use the rear USB port on units that have two ports.
I have had units that will not recover.
Try using the same software as was in the unit when it crashed, not the new update software.
You must use the correct software, ie that for the V7HD for the V7HD etc, not software for any other freesat units.
Try even older software as the file for flash.bin.
Look at the LED in the USB stick. When the TV shows the message "USB Upgrade, do not turn off" you should see the LED on the USB flash as the file is loaded.
The USB LED should also flash a few times as the unit first powers on and looks at it.
Also users have said to use the rear USB port for this on V8 units.
Good luck
Owen
If it powers on but does not complete the boot and stays with no picture to the TV and only a single green light then you can try a flash.bin recovery.
flash.bin recovery is done like this.
Place a copy of the unpacked software (the .bin file) on a USB stick and rename it "flash.bin"
With the USB in the unit, power on while repeat pressing "Menu" on the remote. You must use the V7 remote on the V7.
The unit should reload the software.
Also other users say that you must use a USB stick, not a card holder etc and that stick must be 32Gb or under.
Use the rear USB port on units that have two ports.
I have had units that will not recover.
Try using the same software as was in the unit when it crashed, not the new update software.
You must use the correct software, ie that for the V7HD for the V7HD etc, not software for any other freesat units.
Try even older software as the file for flash.bin.
Look at the LED in the USB stick. When the TV shows the message "USB Upgrade, do not turn off" you should see the LED on the USB flash as the file is loaded.
The USB LED should also flash a few times as the unit first powers on and looks at it.
Also users have said to use the rear USB port for this on V8 units.
Good luck
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: Boot se enciende y se apaga
Hice lo que me indico se hizo todo correcto pero a los 5 minutos se vuelve apagar y encender, asi costante mente, creo q este aparato me ha durado ni 3 meses de funcionamiento
Re: Boot se enciende y se apaga
Trata de entrar a la sección de menu y hacer Factory Reset varias veces durante los 5 minutos. También trata de hacer una actualización por el Menú de USB upgrade con otro archivo durante esos 5 minutos. Durante esos 5 minutos desconecta el coaxial de tu plato. También puedes añadir temporeramente un abanico al lado de la unidad durante ese proceso para ver si se esta sobre calentando