Hola gracias de antemano.
He instalado varios de estos aparatos y me funcionan sin problema, pero uno en concreto la semana pasada se me ha quedado bloqueado.
El aparato esta con luz azul pero la tv no lo reconoce ni por hdmi ni por av, he probado con varios cables y en distintas tv y nada, se le ocurre a alguien algo?
ifire enciende pero no se ve en la tv
Moderators: admin, GTMedia Team
-
- Posts: 221
- Joined: Tue Jan 07, 2020 1:45 am
- Location: Egipto
Re: ifire enciende pero no se ve en la tv
Hola, ¿probaste a cambiar el cable de red?
¿Probaste a cambiar el HDMI?
¿Probaste a cambiar el HDMI?
Saludos.
Re: ifire enciende pero no se ve en la tv
Try a flash.bin recovery if the unit does not show anything on the display, just the blue light.miguelalegria wrote: ↑Tue Aug 25, 2020 10:40 amHola gracias de antemano.
He instalado varios de estos aparatos y me funcionan sin problema, pero uno en concreto la semana pasada se me ha quedado bloqueado.
El aparato esta con luz azul pero la tv no lo reconoce ni por hdmi ni por av, he probado con varios cables y en distintas tv y nada, se le ocurre a alguien algo?
The other GT Media unit have a green button option to change from PAL to NTSC TV format.
lash.bin recovery is done like this.Added fast key to switch video output mode or format.
we try to support some old TV or some signal mode TV
Press menu key to main menu.(Panel show "----")
press Green key to switch NTSC/PAL, the panel will show "PAL " or "NTSC"
Press Stop key to switch the video format
PAL mode : the panel will show "576I" -- "576P" -- "720P"(50HZ) --"1080I"(50HZ) --"1080P"(50HZ)
NTSC mode : the panel will show "480I" -- "480P" -- "720P"(60HZ) --"1080I"(60HZ) --"1080P"(60HZ)
Place a copy of the unpacked software (the .bin file) on a USB stick and rename it "flash.bin"
With the USB in the unit, power on while repeat pressing "Menu" on the remote.
The unit should reload the software.
Also other users say that you must use a USB stick, not a card holder etc and that stick must be 32Gb or under.
Use the rear USB port on units that have two ports.
I have had units that will not recover.
Try using the same software as was in the unit when it crashed, not the new update software.
You must use the correct software, ie that for the V7HD for the V7HD etc, not software for any other freesat units.
Try even older software as the file for flash.bin.
Look at the LED in the USB stick. When the TV shows the message "USB Upgrade, do not turn off" you should see the LED on the USB flash as the file is loaded.
The USB LED should also flash a few times as the unit first powers on and looks at it.
Also users have said to use the rear USB port for this on V8 units.
Good luck
New information: Users are reporting that naming the file "Flash.bin" with a capital has worked where "flash.bin" has not.
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: ifire enciende pero no se ve en la tv
hola tengo un gt-media i-fire y estaba viendo la tele y de repente se fue la señal el aparato estaba encendido pero no daba señal y no me dejaba usar el mando para apagar ni acceder a nada lo desenchufaba y volvia enchufar salia el logo y el texto gt-media y luego seguia sin señal
¿alguien podria ayudarme?
¿alguien podria ayudarme?
-
- Posts: 1
- Joined: Sun Feb 07, 2021 9:25 am
Re: ifire enciende pero no se ve en la tv
Hola a mí me pasa lo mismo.
Alguien me puede ayudar.
Graciass
Alguien me puede ayudar.
Graciass
Re: ifire enciende pero no se ve en la tv
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.