GTMEDIA V8Finder-V71 esta muerto
Moderators: admin, GTMedia Team
GTMEDIA V8Finder-V71 esta muerto
Hello companions, I have a v8 _V71HD finder and I put a list of astra satellite channels from that day, only the GT media logo comes out, then it goes black in patches and tried to put the Firmware back by USB, all of them are in the page method of pressing menu key I get mess up! USB upgrade do not power off! but it is renounced every second does nothing to me, see if there is anyone can help to repair the finder v8 _V71HD thanks to all.
Re: GTMEDIA V8Finder-V71 esta muerto
Check that you have the correct software, the V71 not the newer V73.
Also you must unpack the .zip folder and use the .bin file.
Owen
Also you must unpack the .zip folder and use the .bin file.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: GTMEDIA V8Finder-V71 esta muerto
under the page tested all v71 that I see left pressed menu key that the USB is switched on is paid so it stays usb I do not see that it finishes starting usb left almost 3 minutes but nothing is I do not have a firmware to start the v71 I have backup.
Re: GTMEDIA V8Finder-V71 esta muerto
Here are the full instructions for USB recovery.
Check your USB size etc.
flash.bin recovery is done like this.
Place a copy of the unpacked software (the .bin file) on a USB stick and rename it "flash.bin"
With the USB in the unit, power on while repeat pressing "Menu" on the remote. You must use the V7 remote on the V7.
The unit should reload the software.
Also other users say that you must use a USB stick, not a card holder etc and that stick must be 32Gb or under.
Use the rear USB port on units that have two ports.
I have had units that will not recover.
Try using the same software as was in the unit when it crashed, not the new update software.
You must use the correct software, ie that for the V7HD for the V7HD etc, not software for any other freesat units.
Try even older software as the file for flash.bin.
Look at the LED in the USB stick. When the TV shows the message "USB Upgrade, do not turn off" you should see the LED on the USB flash as the file is loaded.
The USB LED should also flash a few times as the unit first powers on and looks at it.
Also users have said to use the rear USB port for this on V8 units.
Good luck
Owen
Check your USB size etc.
flash.bin recovery is done like this.
Place a copy of the unpacked software (the .bin file) on a USB stick and rename it "flash.bin"
With the USB in the unit, power on while repeat pressing "Menu" on the remote. You must use the V7 remote on the V7.
The unit should reload the software.
Also other users say that you must use a USB stick, not a card holder etc and that stick must be 32Gb or under.
Use the rear USB port on units that have two ports.
I have had units that will not recover.
Try using the same software as was in the unit when it crashed, not the new update software.
You must use the correct software, ie that for the V7HD for the V7HD etc, not software for any other freesat units.
Try even older software as the file for flash.bin.
Look at the LED in the USB stick. When the TV shows the message "USB Upgrade, do not turn off" you should see the LED on the USB flash as the file is loaded.
The USB LED should also flash a few times as the unit first powers on and looks at it.
Also users have said to use the rear USB port for this on V8 units.
Good luck
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: GTMEDIA V8Finder-V71 esta muerto
Hello everyone, I put, if someone knew how to repair GTMEDIA V8Finder-V71 after putting an Astra List, I died, just turned on the logo left dead I was doing a lot of things and another said what to do at the end reading and testing at the end I have found the selection that has solved the problem for me, it worked for me and explained under this line.
1 have the correct GTMEDIA V8Finder-V71 Firmware.
2 USB format 32ft greater than 4 GB to 32 GB higher no
3 much say change name firmware another name there is no flash.bin so it recognizes you well
4 put usb paid GTMEDIA V8Finder-V71 in cendelo the menu button to wait for 10 seconds the usb figa light will stay and start to update the GTMEDIA V8Finder-V71 until the only one renounces only already, then I do a search channel channel. I already had the Astra list my case.
1 have the correct GTMEDIA V8Finder-V71 Firmware.
2 USB format 32ft greater than 4 GB to 32 GB higher no
3 much say change name firmware another name there is no flash.bin so it recognizes you well
4 put usb paid GTMEDIA V8Finder-V71 in cendelo the menu button to wait for 10 seconds the usb figa light will stay and start to update the GTMEDIA V8Finder-V71 until the only one renounces only already, then I do a search channel channel. I already had the Astra list my case.