Busqueda unica frecuencia Mars

[Bronco]

Hola estoy trasteando y no consigo buscar canales en una unica frecuencia podeis ayudarme como hacerla gracias.

[STRETCH]

What transponder are you trying to scan from what satellite.
Also what receiver do you have, with more information, users will be able to help.

Den

[cpr43]

Hola estoy trasteando y no consigo buscar canales en una unica frecuencia podeis ayudarme como hacerla gracias.

Menu

Instalacion

OK

Hacia abajo Tranponder

OK

Busca la frecuencia

OK

Baja hasta la segunda pagina

Comenzar busqueda

Flecha hacia la derecha y cambiar a busqueda de TP

OK

[Bronco]

Hola es v8uhd y hago lo que me dices cpr43 y me busca todos los transponderes salen 103.
Alguna idea que hago maal

Una cosa mas este firm no tiene para buscar hispasat 30W.

[STRETCH]

As i have asked before what channels are you after from the satellite at 30w, from what transponder.

Den

[Bronco]

12398 H 27500
12246 H 27500
Y alguno mas....
Hispasat 30w

[Bronco]

Gracias ya he solucionado añadienfo la frecuencia y satelite.

[raskacielos]

Y como has añadido el satélite?

[STRETCH]

Can we confirm what receiver that you have, with what software, plus what satellite you wish to add.

Den

[raskacielos]

Tengo v8 uhd con la ultima version de mars y me gustaria añadir los canales de hispasat

[STRETCH]

The satellite may already be within the data base of the receiver, if not info as follows.
Menu / Installation / 0000 / OK / With the curser on (Antenna Setting) / OK / At the Bottom of the screen will be a (Red) dot / Press (Red) on the remote / At the next screen, the curser will be on (Satellite Angle), with the remote press 3,0,0 / Then move the curser Down to (Satellite Direction) then with the Arrows on the remote move to Right, West will come up,/ Band will say (Ku) leave as it is / OK / The new satellite name will appear at the top of the screen,/ at this point you could rename it to the name of your new satellite, by Pressing (Blue) on the remote, Press (INFO) on the remote, this will Delete the (Ku-NEW SAT (30W), with the arrows on the remote move to the letters of your new satellite, at each letter Press OK, when complete, move the curser to the word OK, then Press OK on the remote, this will put the name of your new satellite into the receiver, so when all is complete, when you press (SAT) on the remote a list of satellites will come up that you have scanned into the receiver.
Next thing to do is put in a transponder, which is from that satellite, so move the curser Down to (Transponder), then press (Red) again on the remote, put in 12548 at the (Frequency), move the curser down to Polarisation, at this time you do not have to do anything, move the curser Down again to (Symbol Rate) put in 29600 / OK. If you have got you dish already pointing at 30w, you should get a signal reading, move the UP. to (Start Search), with the arrows on the remote move left/right till you see (TP Search), then Move the curser Up again to (Scan Mode), again with the arrows move Left/Right until you see (TV Channels), then move the Curse back Down to (Start Search), then Press OK, at the next screen the curser will be on (NO) just Press OK Again, it will then carry out a scan, when finished, a window will come to the screen, (Information TV : 16 Radio : 0), press Exit, the receiver will go to one of the channels found.
The transponder details that i have given is for some Abertis channels.

Hope this helps

Den

[raskacielos]

Muchísimas gracias. Muy bien explicado