Problems signal gtmedia v8x
Moderators: admin, GTMedia Team
Problems signal gtmedia v8x
I have problems when turn on, signal not found, it should be good signal, I don't know what I do.
Re: Problems signal gtmedia v8x
Can you give us more information, what satellite, transponder, channel.
What message is on tv screen, does the receiver power up, are you using SCART or HDMI.
Den
What message is on tv screen, does the receiver power up, are you using SCART or HDMI.
Den
Re: Problems signal gtmedia v8x
Any satellite, any transponder, is like wire cutted, signal=0, quality=0, when I put between other receptor in stand by, I can watch, It have sigal.
Re: Problems signal gtmedia v8x
Message is "no signal", I use HDMI.
Re: Problems signal gtmedia v8x
is it the tv that does not detect the HDMI or the decorder does not lock signal of the channel, please elaborate further.
Re: Problems signal gtmedia v8x
I can to enter to all menus although put "moving motor" do not nothing.
- Attachments
-
- IMG_20200701_173024.jpg (2.79 MiB) Viewed 1804 times
Re: Problems signal gtmedia v8x
Is your system a fixed dish or a motorised, have you checked all connections etc.
Den
Den
Last edited by STRETCH on Wed Jul 01, 2020 5:11 pm, edited 2 times in total.
Re: Problems signal gtmedia v8x
Understanding the SIGNAL and QUALITY readings on the antenna display page of your receiver:
(a) S=0 Q=0.....no lnb connected or bad coax or bad lnb
(b) S=70 Q=0.....lnb connected no signal from satellite (the 70 is noise generated by the lnb)
(c) S=70 Q=70.....lnb connected, signal from satellite OK, adjust for max Q.
(a) S=0 Q=0.....no lnb connected or bad coax or bad lnb
(b) S=70 Q=0.....lnb connected no signal from satellite (the 70 is noise generated by the lnb)
(c) S=70 Q=70.....lnb connected, signal from satellite OK, adjust for max Q.
No live links (Rule #18) highlight the URL and use the Code tag option "</>"
V7HD, V8SUPER, V8X, V7PRO, GTC, FORMULER F4(TURBO)
V7HD, V8SUPER, V8X, V7PRO, GTC, FORMULER F4(TURBO)
Re: Problems signal gtmedia v8x
I have motorised dish, with other reciver all satellites works ok, lnb and motor is conected ok, the wire is 25 meters aprox, when I put a wire of 10 meters all works ok. When I bougth the reciver, some days works ok, but now never works.
Re: Problems signal gtmedia v8x
Have you got a spare power supply of the same amp, to try
Den
Den
Re: Problems signal gtmedia v8x
I don't understand you, I have only two recivers, gtmedia and mvision, one motor and one dish. When I connect the reciver like bridge in stand by, I have signal in gtmedia, but I don't want use mvision.
Re: Problems signal gtmedia v8x
Do you speak spanish?
Look this.
Look this.
- Attachments
-
- Sin título.jpg (104.93 KiB) Viewed 1772 times
Re: Problems signal gtmedia v8x
The 22mtr cable that you have (there must be a short some were (for the MVISION receiver is (amplifying the signal) with you using it as a loop-through)
So with a cable of a short length direct to the V8x from the motor everything works.
Which points to 22mtr cable needs to be looked at, check connectors etc, ( for a trial try a new cable of the length required (just lay it loose from the motor to the V8x)(that is if the other half will let you run cables all over the place) and see what results you get.
Good Luck
Den
So with a cable of a short length direct to the V8x from the motor everything works.
Which points to 22mtr cable needs to be looked at, check connectors etc, ( for a trial try a new cable of the length required (just lay it loose from the motor to the V8x)(that is if the other half will let you run cables all over the place) and see what results you get.
Good Luck
Den
Re: Problems signal gtmedia v8x
I can replace the wire but I don't know if solve this problem because I think the wire is too long. The first days when I bought it, sometimes I had a signal with the long wire, but now never.
Re: Problems signal gtmedia v8x
The length should not matter, just try it, and see what results you get.
I have a V8x, my cable run is more than 22mts, with 100cm dish my readings on transponder 12548v 29600 is S93% Q77% I am based in the west midlands uk.
Good Luck
Den
I have a V8x, my cable run is more than 22mts, with 100cm dish my readings on transponder 12548v 29600 is S93% Q77% I am based in the west midlands uk.
Good Luck
Den
Re: Problems signal gtmedia v8x
I do not know if it will be due to the length or because when passing it through the roof, it bent several times.
Thanks.
Thanks.
Re: Problems signal gtmedia v8x
From what you say, the cable may have been in place for a while, so I would think it would be best to replace it and get a few more years service, as you know cable does perish over time.
Den
Den
Re: Problems signal gtmedia v8x
The wire is new, two months approx., 3 months ago, I bought the first reciver gtmedia in amazon, the same happened, sometimes had signal sometimes no signal and while recording appears in tv "usb error", I returned to amazon, and after I bougth the same reciver in aliexpress.
Re: Problems signal gtmedia v8x
I have this too.
It is something is the software.
I will do some tests today and report here and to GT Media.
I wonder if it is the unit does not send DiSEqC commands on power up? If so then any channel on DiSEqC switch port 1 should start after power on.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: Problems signal gtmedia v8x
DiSEqc1.2 function you useFeralkiwi wrote: ↑Wed Jul 01, 2020 10:45 pmI have this too.
It is something is the software.
I will do some tests today and report here and to GT Media.
I wonder if it is the unit does not send DiSEqC commands on power up? If so then any channel on DiSEqC switch port 1 should start after power on.
Owen
1. Under the satellite list, switch to rotate the satellite antenna,
2. Under the program playback, switch satellite DiSEqc1.2 function mobile satellite antenna, the function has been increased, you can go to download the latest firmware
FREESAT brand change GT MEDlA
Re: Problems signal gtmedia v8x
I have downloaded the last software and I can't solve this problem.