GTMEDIA_V8 Series Bug Tracking System
Moderators: admin, GTMedia Team
Re: GTMEDIA_V8 Series Bug Tracking System
Hello, GTMedia Team
I found a bug.
In blind scan mode
V8UHD can be recognized and demodulated,
V8X can be recognized but cannot be demodulated.
Below.
JCSAT-2B Ku
TV asahi feeds
Postscript.
constant.cw
2600: 0000000: 0001: 0100: 1fff: 0200: 1111111111111111
2600: 0000000: 0001: 0100: 1fff: 0200: 2222222222222222
2600: 0000000: 0001: 0100: 1fff: 0200: 3333333333333333
Please correct so that 1 2 3 can be identified even in the above state.
Thank you.
skewer
I found a bug.
In blind scan mode
V8UHD can be recognized and demodulated,
V8X can be recognized but cannot be demodulated.
Below.
JCSAT-2B Ku
TV asahi feeds
Postscript.
constant.cw
2600: 0000000: 0001: 0100: 1fff: 0200: 1111111111111111
2600: 0000000: 0001: 0100: 1fff: 0200: 2222222222222222
2600: 0000000: 0001: 0100: 1fff: 0200: 3333333333333333
Please correct so that 1 2 3 can be identified even in the above state.
Thank you.
skewer
Last edited by skewer on Wed Jan 13, 2021 11:22 am, edited 2 times in total.
Re: GTMEDIA_V8 Series Bug Tracking System
Hello. New V220 firmware did not fix this issue. Will it be fixed in the next firmware release? Thank you.Tom.w wrote: ↑Thu Dec 24, 2020 3:01 amhelloncansan wrote: ↑Thu Dec 24, 2020 1:01 amHello. Any update about this issue?Tom.w wrote: ↑Mon Dec 14, 2020 3:51 amok,we will check and fix it.ncansan wrote: ↑Sun Dec 13, 2020 11:51 amSimilar issue with my V8 UHD with latest firmware. Everytime I switch on, cccam lines are in idle state. I have to stop the cccam line and start again and then it works ok. And when I said 'switch on', it means from standby state, I don't remove power supply.belmonte wrote: ↑Wed Dec 02, 2020 5:23 amHello,
1.- In the last firmware (a some previous also) I have to turn on cccam lines every time a power on the box, by default the cccam lines are off when a power on the box, despite I have save the cccam lines correctly.
2.- I don't know when and from time to time but some times the image turns green, I have to restart the box or change the display to PAL, Auto or NTSC to watch the image with normal colors
Regards.
I have found out more information. If DHCP is off, when I turn on the V8 UHD, I have to turn off the cccam lines and then on, in order to open the channels. But if DHCP is on, then I can see properly the channels without turning off-on the cccam lines. So it seems it is a bug only if DHCP is off.
However I need DHCP off to choose different DNS servers for the iptv service. Please check if the bug can be fixed.
thank you very much for your detail information.
we will fix it.
Re: GTMEDIA_V8 Series Bug Tracking System
Latest software V220, unable to scan in the (streaming ) channels on 5w,(ie 12648v 29500 PSLN Gold 121212). Signal (not found) (grey). Fransat channels found.
The software V219 was able to scan in the said channels, with the PSLN (Auto detect) set to (ON), and also been able to scan in the said channels when you add the (PSLN) Info to the transponder details. (which i helped to test).
Unable to down grade to V219, comes up as (invalid file).
Den
The software V219 was able to scan in the said channels, with the PSLN (Auto detect) set to (ON), and also been able to scan in the said channels when you add the (PSLN) Info to the transponder details. (which i helped to test).
Unable to down grade to V219, comes up as (invalid file).
Den
Re: GTMEDIA_V8 Series Bug Tracking System
thank you.STRETCH wrote: ↑Wed Jan 13, 2021 11:08 amLatest software V220, unable to scan in the (streaming ) channels on 5w,(ie 12648v 29500 PSLN Gold 121212). Signal (not found) (grey). Fransat channels found.
The software V219 was able to scan in the said channels, with the PSLN (Auto detect) set to (ON), and also been able to scan in the said channels when you add the (PSLN) Info to the transponder details. (which i helped to test).
Unable to down grade to V219, comes up as (invalid file).
Den
We will check it ASAP
Re: GTMEDIA_V8 Series Bug Tracking System
PLSN have you opened,STRETCH wrote: ↑Wed Jan 13, 2021 11:08 amLatest software V220, unable to scan in the (streaming ) channels on 5w,(ie 12648v 29500 PSLN Gold 121212). Signal (not found) (grey). Fransat channels found.
The software V219 was able to scan in the said channels, with the PSLN (Auto detect) set to (ON), and also been able to scan in the said channels when you add the (PSLN) Info to the transponder details. (which i helped to test).
Unable to down grade to V219, comes up as (invalid file).
Den
System Setup----PLSN----ON
FREESAT brand change GT MEDlA
Re: GTMEDIA_V8 Series Bug Tracking System
@ Lining
With the new software, i have tried to scan with the (PSLN) set at (OFF) and (ON), with both settings the signal is (GREY).
Since i helped with the testing of this option, the (PSLN) is set to (ON).
Den
With the new software, i have tried to scan with the (PSLN) set at (OFF) and (ON), with both settings the signal is (GREY).
Since i helped with the testing of this option, the (PSLN) is set to (ON).
Den
Re: GTMEDIA_V8 Series Bug Tracking System
Yesncansan wrote: ↑Wed Jan 13, 2021 10:47 amHello. New V220 firmware did not fix this issue. Will it be fixed in the next firmware release? Thank you.Tom.w wrote: ↑Thu Dec 24, 2020 3:01 amhelloncansan wrote: ↑Thu Dec 24, 2020 1:01 amHello. Any update about this issue?Tom.w wrote: ↑Mon Dec 14, 2020 3:51 amok,we will check and fix it.ncansan wrote: ↑Sun Dec 13, 2020 11:51 amSimilar issue with my V8 UHD with latest firmware. Everytime I switch on, cccam lines are in idle state. I have to stop the cccam line and start again and then it works ok. And when I said 'switch on', it means from standby state, I don't remove power supply.belmonte wrote: ↑Wed Dec 02, 2020 5:23 amHello,
1.- In the last firmware (a some previous also) I have to turn on cccam lines every time a power on the box, by default the cccam lines are off when a power on the box, despite I have save the cccam lines correctly.
2.- I don't know when and from time to time but some times the image turns green, I have to restart the box or change the display to PAL, Auto or NTSC to watch the image with normal colors
Regards.
I have found out more information. If DHCP is off, when I turn on the V8 UHD, I have to turn off the cccam lines and then on, in order to open the channels. But if DHCP is on, then I can see properly the channels without turning off-on the cccam lines. So it seems it is a bug only if DHCP is off.
However I need DHCP off to choose different DNS servers for the iptv service. Please check if the bug can be fixed.
thank you very much for your detail information.
we will fix it.
we have fixed this issue. it will release in the next firmware.
Re: GTMEDIA_V8 Series Bug Tracking System
No hay modo de salir de esta pantalla
- Attachments
-
- IMG_20210114_152920_924.jpg (86.43 KiB) Viewed 6435 times
Re: GTMEDIA_V8 Series Bug Tracking System
For V8 UHD
Many FWs back and still... Astra 3B is not 13.0E, but 23.5E
When I select / switch chanel via (OK - channel list - select by arrows - OK) no info screen... I must press INFO.
Select by Up and Down (previous / next) opens info screen correctly (without going through channel list).
Not Bug, but I would like to open discuss about info screens. Press INFO 1x and press INFO 2x... The first one is OK, but the second - why this screen?
The most of infos on this screen are the same - redundant (only in different design).
But detailed infos about actual movie are not here... I preferred this info (detailed from EPG). Simply press 2x INFO and gets this detailed info about actual movie... What do you think about this? Change the redundat infos to actual movie detailed info? Improvement? (Like V7plus)
Many FWs back and still... Astra 3B is not 13.0E, but 23.5E
When I select / switch chanel via (OK - channel list - select by arrows - OK) no info screen... I must press INFO.
Select by Up and Down (previous / next) opens info screen correctly (without going through channel list).
Not Bug, but I would like to open discuss about info screens. Press INFO 1x and press INFO 2x... The first one is OK, but the second - why this screen?
The most of infos on this screen are the same - redundant (only in different design).
But detailed infos about actual movie are not here... I preferred this info (detailed from EPG). Simply press 2x INFO and gets this detailed info about actual movie... What do you think about this? Change the redundat infos to actual movie detailed info? Improvement? (Like V7plus)
Re: GTMEDIA_V8 Series Bug Tracking System
I have 3x V7 Plus and 2x V8 UHD...
What about to add the selection dialog to CCCam import?
Like Koqit...
What about to add the selection dialog to CCCam import?
Like Koqit...
Re: GTMEDIA_V8 Series Bug Tracking System
As 2600 is BISS, I would put your codes into the BISS section of the conditional access / key edit menu, not the CW section.skewer wrote: ↑Wed Jan 13, 2021 8:27 amHello, GTMedia Team
I found a bug.
In blind scan mode
V8UHD can be recognized and demodulated,
V8X can be recognized but cannot be demodulated.
Below.
JCSAT-2B Ku
TV asahi feeds
Postscript.
constant.cw
2600: 0000000: 0001: 0100: 1fff: 0200: 1111111111111111
2600: 0000000: 0001: 0100: 1fff: 0200: 2222222222222222
2600: 0000000: 0001: 0100: 1fff: 0200: 3333333333333333
Please correct so that 1 2 3 can be identified even in the above state.
Thank you.
skewer
The V8X may work that way.
Note the auto BISS function adds the codes to the MGBISS section. You can find them from there and add then to the normal BISS if you know which channel they are for.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: GTMEDIA_V8 Series Bug Tracking System
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: GTMEDIA_V8 Series Bug Tracking System
Thank you.Feralkiwi wrote: ↑Sat Jan 16, 2021 11:36 pmAs 2600 is BISS, I would put your codes into the BISS section of the conditional access / key edit menu, not the CW section.skewer wrote: ↑Wed Jan 13, 2021 8:27 amHello, GTMedia Team
I found a bug.
In blind scan mode
V8UHD can be recognized and demodulated,
V8X can be recognized but cannot be demodulated.
Below.
JCSAT-2B Ku
TV asahi feeds
Postscript.
constant.cw
2600: 0000000: 0001: 0100: 1fff: 0200: 1111111111111111
2600: 0000000: 0001: 0100: 1fff: 0200: 2222222222222222
2600: 0000000: 0001: 0100: 1fff: 0200: 3333333333333333
Please correct so that 1 2 3 can be identified even in the above state.
Thank you.
skewer
The V8X may work that way.
Note the auto BISS function adds the codes to the MGBISS section. You can find them from there and add then to the normal BISS if you know which channel they are for.
Owen
Feralkiwi
Re: GTMEDIA_V8 Series Bug Tracking System
No me vale el forzado, alguna idea
- Attachments
-
- IMG_20210114_152920_924.jpg (86.43 KiB) Viewed 6243 times
Re: GTMEDIA_V8 Series Bug Tracking System
I'm doing it with the most current one and she says no, it keeps coming out as shown
- Attachments
-
- IMG_20210114_152920_924.jpg (86.43 KiB) Viewed 6213 times
Re: GTMEDIA_V8 Series Bug Tracking System
That is the service screen.
You need to do a recovery by flash.bin.
I also replied to your Friday post on this.
If you are having problems finding your posts, use the "Quick Links" button at the top left and then "Your Posts".
Owen
alex.c
Please note this is happening a to a LOT of users.
viewtopic.php?f=33&t=21193&p=91110&hilit=service#p91110
viewtopic.php?f=33&t=21192&p=90824&hilit=service#p90824
viewtopic.php?f=33&t=21315&p=91562&hili ... es.#p91562
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: GTMEDIA_V8 Series Bug Tracking System
Don't downgrade firmware to the version lower than the one came from factory.Feralkiwi wrote: ↑Tue Jan 19, 2021 8:10 pmThat is the service screen.
You need to do a recovery by flash.bin.
I also replied to your Friday post on this.
If you are having problems finding your posts, use the "Quick Links" button at the top left and then "Your Posts".
Owen
alex.c
Please note this is happening a to a LOT of users.
viewtopic.php?f=33&t=21193&p=91110&hilit=service#p91110
viewtopic.php?f=33&t=21192&p=90824&hilit=service#p90824
viewtopic.php?f=33&t=21315&p=91562&hili ... es.#p91562
Owen
I don't know why a lot of user like to downgrade the firmware.
The newer shoud always be better then the older.
Re: GTMEDIA_V8 Series Bug Tracking System
The main reason why users down grade, is because when they do upgrade, the receiver DOES NOT do what it did before the upgrade.
Everyone users their receiver in different ways, as they say (you cannot please all people all the time.
Den
Everyone users their receiver in different ways, as they say (you cannot please all people all the time.
Den
Re: GTMEDIA_V8 Series Bug Tracking System
That's true.
But please remember that don't downgrade firmware to the version lower than the one came from factory.
Re: GTMEDIA_V8 Series Bug Tracking System
Please alex.calex.c wrote: ↑Wed Jan 20, 2021 3:37 amDon't downgrade firmware to the version lower than the one came from factory.Feralkiwi wrote: ↑Tue Jan 19, 2021 8:10 pmThat is the service screen.
You need to do a recovery by flash.bin.
I also replied to your Friday post on this.
If you are having problems finding your posts, use the "Quick Links" button at the top left and then "Your Posts".
Owen
alex.c
Please note this is happening a to a LOT of users.
viewtopic.php?f=33&t=21193&p=91110&hilit=service#p91110
viewtopic.php?f=33&t=21192&p=90824&hilit=service#p90824
viewtopic.php?f=33&t=21315&p=91562&hili ... es.#p91562
Owen
I don't know why a lot of user like to downgrade the firmware.
The newer should always be better then the older.
This report was not about downgrades.
This report is about many users finding their unit locked in the service screen
.
. Owen
Note all users:
What alex.c is saying about downgrading is that downgrades is OK but not to downgrade below the version that was in your unit when you brought it.
This will be because the software below factory supplied will look for hardwired programs that may not be there with hardware produced after that software.
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
Re: GTMEDIA_V8 Series Bug Tracking System
I think there is a bug in record when you try program a record with cline.
1) you program the record.
2) it wake up in time.
3) it jumps to the selected channel to record.
4) if v8x try record to early the channel when the image is not displayed after jump to it, It shows a service error, he don't record anything and it shutdown in the programed time.
So it fail.
I think can be solved easy adding a few seconds delay or start recording only when the channel is on.
Or let record even if channel is codified.
1) you program the record.
2) it wake up in time.
3) it jumps to the selected channel to record.
4) if v8x try record to early the channel when the image is not displayed after jump to it, It shows a service error, he don't record anything and it shutdown in the programed time.
So it fail.
I think can be solved easy adding a few seconds delay or start recording only when the channel is on.
Or let record even if channel is codified.
Last edited by Satman13 on Thu Jan 21, 2021 12:18 pm, edited 3 times in total.
Re: GTMEDIA_V8 Series Bug Tracking System
Exactly, this is what I meant.Feralkiwi wrote: ↑Wed Jan 20, 2021 8:45 pmPlease alex.calex.c wrote: ↑Wed Jan 20, 2021 3:37 amDon't downgrade firmware to the version lower than the one came from factory.Feralkiwi wrote: ↑Tue Jan 19, 2021 8:10 pmThat is the service screen.
You need to do a recovery by flash.bin.
I also replied to your Friday post on this.
If you are having problems finding your posts, use the "Quick Links" button at the top left and then "Your Posts".
Owen
alex.c
Please note this is happening a to a LOT of users.
viewtopic.php?f=33&t=21193&p=91110&hilit=service#p91110
viewtopic.php?f=33&t=21192&p=90824&hilit=service#p90824
viewtopic.php?f=33&t=21315&p=91562&hili ... es.#p91562
Owen
I don't know why a lot of user like to downgrade the firmware.
The newer should always be better then the older.
This report was not about downgrades.
This report is about many users finding their unit locked in the service screen
.
.
Servicec_Screen2.jpg
Owen
Note all users:
What alex.c is saying about downgrading is that downgrades is OK but not to downgrade below the version that was in your unit when you brought it.
This will be because the software below factory supplied will look for hardwired programs that may not be there with hardware produced after that software.
If anybody did this, the only way is to do the force upgrade to the latest firmware.
Re: GTMEDIA_V8 Series Bug Tracking System
Are you saying that this service screen is coming up as a result of users trying to load too old a version of software?
No user has reported this as a cause.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.