V7pro cannot booting
Moderators: admin, GTMedia Team
-
- Posts: 12
- Joined: Fri Jan 29, 2021 6:23 am
V7pro cannot booting
I have v7pro it can't operate, only the green light is on, please solve it
Re: V7pro cannot booting
Use the search bar at right top cornerSaipul yadi wrote: ↑Wed Jul 07, 2021 11:52 amI have v7pro it can't operate, only the green light is on, please solve it
Look for USB Flash.bin recovery process
Re: V7pro cannot booting
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
-
- Posts: 12
- Joined: Fri Jan 29, 2021 6:23 am
Re: V7pro cannot booting
can't flash, have tried repeatedly, no signal is detected on tv, initially it was normal, but when it was restarted the red light didn't turn on, only the green light,
Re: V7pro cannot booting
Here are my notes on flash.bin.
flash.bin recovery is done like this.
Place a copy of the unpacked software (the .bin file) on a USB stick and rename it "flash.bin"
With the USB in the unit, power on while repeat pressing "Menu" on the remote.
The unit should reload the software.
Also other users say that you must use a USB stick, not a card holder etc and that stick must be 32Gb or under.
Use the rear USB port on units that have two ports.
I have had units that will not recover.
Try using the same software as was in the unit when it crashed, not the new update software.
You must use the correct software, ie that for the V7HD for the V7HD etc, not software for any other freesat units.
Try even older software as the file for flash.bin.
Look at the LED in the USB stick. When the TV shows the message "USB Upgrade, do not turn off" you should see the LED on the USB flash as the file is loaded.
The USB LED should also flash a few times as the unit first powers on and looks at it.
Also users have said to use the rear USB port for this on V8 units.
Good luck
New information: Users are reporting that naming the file "Flash.bin" with a capital has worked where "flash.bin" has not. This is with the Nova units mostly.
Owen
flash.bin recovery is done like this.
Place a copy of the unpacked software (the .bin file) on a USB stick and rename it "flash.bin"
With the USB in the unit, power on while repeat pressing "Menu" on the remote.
The unit should reload the software.
Also other users say that you must use a USB stick, not a card holder etc and that stick must be 32Gb or under.
Use the rear USB port on units that have two ports.
I have had units that will not recover.
Try using the same software as was in the unit when it crashed, not the new update software.
You must use the correct software, ie that for the V7HD for the V7HD etc, not software for any other freesat units.
Try even older software as the file for flash.bin.
Look at the LED in the USB stick. When the TV shows the message "USB Upgrade, do not turn off" you should see the LED on the USB flash as the file is loaded.
The USB LED should also flash a few times as the unit first powers on and looks at it.
Also users have said to use the rear USB port for this on V8 units.
Good luck
New information: Users are reporting that naming the file "Flash.bin" with a capital has worked where "flash.bin" has not. This is with the Nova units mostly.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
-
- Posts: 12
- Joined: Fri Jan 29, 2021 6:23 am
Re: V7pro cannot booting
just like this, can't boot even though I tried with the old firmware, the bin file has been changed to Flash.bin
Re: V7pro cannot booting
Try a different USB stick.
If all fails you may need to use the RS232 method.
Owen
If all fails you may need to use the RS232 method.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
-
- Posts: 12
- Joined: Fri Jan 29, 2021 6:23 am
Re: V7pro cannot booting
maybe you mean this tool
Re: V7pro cannot booting
Yes it was one like that I used on my unit.
There are notes here I wrote for the old V8 Finder. I added a note regard the use of this cable USB to RS232.
Owen
There are notes here I wrote for the old V8 Finder. I added a note regard the use of this cable USB to RS232.
Owen
Dishes; 3x3m, 2.4m and 4.1m, 10+ ku, 2 movers, USARLS. V8 Combo, Pro, V8 Golden, Nova V8Pro2, GTC, Super.V7HDs, Combo and V7s V7Plus Finder, Finder-Meter V8X / UHD V7Pro GT/XCombo. Sats 100.5E to 177W. I'm a Sat hobbyist who helps out.
-
- Posts: 12
- Joined: Fri Jan 29, 2021 6:23 am
Re: V7pro cannot booting
For tcom settings,, choose DDR2 or DDR 3?
Re: V7pro cannot booting
you need to select ddr2