Electronic schematic board GT Media V8 Finder 2

[physicajr]

Could some user or the brand itself provide the electronic schematic of the GT Media V8 Finder 2 board, I could not solve the problem after the update, even rewriting the eprom and changing it, it did not work and it has a very hot component. I used the device twice and after an update I put the charger I was already using before and it still didn't turn on. I'm waiting for the brand or some user who has the schema. The component circled in the image is at high temperature. Thank you very much in advance.

[memov77]

Could you get off metal cap of the tuner and make a photo inside it?

[physicajr]

Could you get off metal cap of the tuner and make a photo inside it?

[memov77]

Thanks, but I can't read what is written on the chip. Can you read and write?

[physicajr]

gtmedia please send the schematic of this satfinder to try to fix it I used it twice I went to update and there was a problem and then an update came out due to loading problems, the update gave a problem on my device. help me please!

[Feralkiwi]

Have you tried a forced recovery?

Owen

[sickboy]

Could some user or the brand itself provide the electronic schematic of the GT Media V8 Finder 2 board, I could not solve the problem after the update, even rewriting the eprom and changing it, it did not work and it has a very hot component. I used the device twice and after an update I put the charger I was already using before and it still didn't turn on. I'm waiting for the brand or some user who has the schema. The component circled in the image is at high temperature. Thank you very much in advance.

What is written on this little ic ?

[Feralkiwi]

The best pics I can.

Owen
.
.

P1014187.JPG (1.03 MiB) Viewed 4028 times

P1014185.JPG (1004.02 KiB) Viewed 4028 times

P1014189.JPG (334.37 KiB) Viewed 4026 times

P1014190.JPG (272.98 KiB) Viewed 4026 times

[CAJE]

The best pics I can.

Owen

A trick for it to come out correctly is to move the cell phone away and activate the X10 zoom, identification will come out perfectly

[Feralkiwi]

The best pics I can.

Owen

A trick for it to come out correctly is to move the cell phone away and activate the X10 zoom, identification will come out perfectly

I used my Olympus SP500 camera on close zoom, and take the shot 40mm away at most.
Light was the issue, no sun that day.

Owen

[gluegun]

Code: Select all

http://www.montage-lz.com/index.php/Index/Product/productInfo?product_id=15

serching result...... china SOC(system on chip) company.

[nabiltag]

[img]

[/

هده صورة الايسي الدي تبحث عن رقمه هدية مني اليك لتسهيل اصلاح جهازك

44a2b22b-2af3-4d8f-8457-847eca9e7874.jpg (262.71 KiB) Viewed 458 times

img]

[nabiltag]

اما الايسي الصغير الدي يسخن فرقمه ياصديقي s35bdl1 عليك بتغيره ومراجعة ومراجعة المقاومات و المكثفاث السطحية التي امامه وقبله قبل التغير

[mitko 20050]

NO SIGNAL PROBLEM IN DVB-S/S2 MODE
Problem: No signal or Low signal in DVB-S/S2 mode.
Check signal cables and LNB voltage, if there is no problem, check M88TS6011 (U3) supply voltages;
3V3_VCC_SAT.
If the above measurements are OK, then measure the voltage from the PIN1 of U3.
If the PIN9 voltage is equal to 0V, please check i2c waveforms and software. If the PIN9 voltage is lower than
1V(e.g: 0.8Vor 0.3V), change the U3 with a new part.