Gtmedia v8uhd 4k problemi con motore disecq 1.2

[Feralkiwi]

Non capisco cosa vuoi dire , i miei dati usals li ho inseriti, ma il motore non gira ugualmente anche perché dalle specifiche risulta sicuramente disecq 1.2 ma non usals

Ma.s v1.11.12645

This motor does look to be DiSEqC ONLY.

Method 1: No positions saved in the motor.
To set those up you need to move the motor using the move west, move east controls in the DiSEqC motor menu, while watching for the signal quality / level on a good known TP for a signal level.
You need to look up what are good active TP's and have their frequencies and SR sent in the TP menu so you can select and use them in the motor menu.
Note for high band TP's with a universal 9750 / 10600 LNB, the motor move command uses the 22kHz tone for sending the command to the motor and then returns it to "ON" after the move, so wait a second or two after the move to allow the LNB to be set back to high band (High band 22kHz tone "ON" is controlled by the "Auto" 22kHz setting in the menus for 9750/10600 universal LNB's)
Fine tune east / west for the best signal / quality.
After you find each satellite, then "Save" the position with the number you want.

Method 2:
If your motor is already set up with saved positions then do this:
Note the position number you have set for each satellite longitude you have set in the motor.
NOTE: When you "Save" the position number in the menu of the V8UHD it is ALSO saved into the motor as the position number for where the motor is now.
So to prevent incorrect positions being saved to a motor already set up do this.
With the LNB cable disconnected, set each satellite up for DiSEqC motor and "Save" the known position number for each.
This saves the position umbers in the V8UHD menus, but not to the Motor.
That done connect the LNB cable and test.

Owen

[STRETCH]

Have found some more information about your motor, which i now know is (diseq 1.2) only.
So carry out your install as per the post from (Owen).

Den

[poggio61]

Il motore l' ho preso usato, come faccio a vedere se ha posizioni salvate ? E soprattutto come lo vedo su v8? Grazie

[poggio61]

Se non ricordo male sul motore ci dovrebbe essere un tastino per il reset, se io resetto il motore mi dici gentilmente il percorso da fare sul gtmedia per impostare sulla posizione 1 hotbird 2 Astra 3 16est e via dicendo? Grazie

[STRETCH]

With you saying that the motor works with your other receivers, check the satellite list, and see what numbers are against each satellite.
Then put the list of those into the V8UHD, which can be done through the Installation / OK / 0000 / OK / Which will put the curser against the Satellite that was watched last / At the Bottom of the screen will a Green dot (Move) / Press Green on the Remote / Then Press on the remote the Number that your list says is for 30w (lets say 2) / OK / The satellite will then move to NO 2 on your list, carry on with rest, then Exit.
Just try it with a couple of satellites, then test to see if it works.

Den

[poggio61]

Probabilmente sono io che sono troppo ignorante in materia, ho fatto quello che dici e mi appare un riquadro al centro del TV che mi dice :"attenzione" 17max TV(16E)
Sposta a 17/62 e io posso fare diventare il 17 qualsiasi altro numero, ma non capisco come fa il motore a memorizzare

[poggio61]

Poi non ho capito perché entrando su installazione ok devo premere 4 volte 0 , anche senza premere 4 volte e spostandosi sul satellite c'è il tasto verde con la scritta sposta

[STRETCH]

Just press 3 the remote, then OK, that satellite would have moved to NO 3 on your channel list, to check this exit out, then Press (sat) on the remote
to see were it is now on your list.

Den

[louisino]

With you saying that the motor works with your other receivers, check the satellite list, and see what numbers are against each satellite.
Then put the list of those into the V8UHD, which can be done through the Installation / OK / 0000 / OK / Which will put the curser against the Satellite that was watched last / At the Bottom of the screen will a Green dot (Move) / Press Green on the Remote / Then Press on the remote the Number that your list says is for 30w (lets say 2) / OK / The satellite will then move to NO 2 on your list, carry on with rest, then Exit.
Just try it with a couple of satellites, then test to see if it works.

Den

Se non ricordo male avevo provato anche io, avendo un posizionatore che gestisce un motore H-H che non posso pilotare in modalità USALS e se non ricordo male non è andato a buon fine questa prova. Poniamo che questa procedura sia fattibile, come fai a memorizzare allo stesso numero i vari provider memorizzati su un singolo satellite?
Solo HotBird a 13est ha 7 provider come faccio a memorizzare tutti e 7 sul singolo satellite? La stessa cosa per Astra 19,2 est e via via tutti gli altri che hanno più provider sullo stesso satellite.
Bisognerebbe configurarsi dei setting personalizzati, ma non esiste un editor dedicato, almeno pubblico.

[STRETCH]

When in the (Installation), the curser has to be on the name of the satellite so that you can then move it.

Den

[louisino]

In that case, i have the said motor, have used it with the following receivers, V7 Pro / V7 S2X / V7 S5X / V8X / V8UHD / GT Combo /
V8 Nova Orange plus other models, have no issues at all.
Just seen your photo's, you may have to replace your cables, put the cables up the pole, then between the stab bracket and pole so that the cable
comes out at the bottom of the motor, put the boots onto the cable, plus the connections may need redoing.
Also check the power supply, you may need one that is 12v 2a.

Den

Ma tu riesci a gestirlo in modalità USALS o con il DiseqC 1.X ?

[louisino]

When in the (Installation), the curser has to be on the name of the satellite so that you can then move it.

Den

Questo lo ho capito e lo ho fatto, ma come ti dicevo in precedenza, su un satellite ci sono più provider da mettere sullo stesso satellite e non esiste una posizione 1a,1b,1c...

[STRETCH]

@ Louisino
Can you confirm what equipment you have receiver/motor/software etc, what satellites you which to view, how you wish to decode them.

Den

[louisino]

@ Louisino
Can you confirm what equipment you have receiver/motor/software etc, what satellites you which to view, how you wish to decode them.

Den

Lo ho scritto prima, ti sarà sfuggito, uso un motore H-H e posizionatoreSuperJack V-Box II che vorrei pilotare con il Gtmedia V8uHD Ma*s, ma non è possibile spostare il motore tramite ricevitore, ma solo tramite posizionatore.
Ho cercato sul forum ed ho trovato questo 3D dove, tu stesso, dici che sposti il motore in modalità Usals con lo stesso motore di Poggio61
viewtopic.php?p=140830#p140830

[STRETCH]

The motor that i have is a TM2300, which has USALS control, which is different to the (Super Jack GT 120) even if the photo's show that they look
the same, the software would be different.
With you both having the same equipment, i will help were i can.

Den

[poggio61]

Tm2300 M2 o M3 ? Funziona al 100% con v8uhd e M.rs ?

[STRETCH]

The motor that i have is the TM2300 M3, which i have had for a lot of years, and as i have said works OK with ALL the GT Media receivers
that i have, using the USALS.
You will be able to purchase one via a well known web site, or a satellite shop near you.

Den